沁水盆地赵庄矿3号煤层地面煤层气抽采低产原因分析

在对沁水盆地赵庄矿煤层气开发地质、煤层气生产井资料深入研究的基础上，分析、总结了区内煤层气直井低产原因，并据此提出了区内地面抽采后续开发方向。研究认为:3号煤层气含量偏低、含气饱和度低、临储比低，致使排采阶段气含量可降幅度低，是其低产的宏观表征；3号煤储层不匹配孔级，较差连通性，即微、小孔为主，中孔次之，大孔不发育，微裂隙连通性差，致使扩散缓慢、影响储层改造和抽采效果，是其低产的微观表征；3号煤层远高于顶底板塑性及相近的水平应力，进一步造成改造缝长受限，泄流面积不足。因此，建议区内后续地面抽采方式应以增大泄流面积开发方式为主。     

卡尔费休法测定液态氯乙烯中水含量的研究

采用卡尔费休法测定了液态氯乙烯单体中的水含量。试验确定了采样工具、样品的预处理方式及选用溶剂的最优方案,并进行了精密度与准确度的验证。结果表明卡尔费休法测定液态氯乙烯单体中的水含量准确、快速,可以用来准确、及时地指导生产。     

氮含量对HPD-1双相不锈钢组织及力学性能的影响

通过显微组织观察与力学性能测试研究了氮含量(0.08%~0.22％,质量分数)对HPD-1双相不锈钢硬度、拉伸性能、低温冲击性能及疲劳性能的影响。结果表明,氮含量变化可显著影响试验钢γ/α相比例,当氮含量由0.08％升高到0.22％,γ相含量由38.1％提高至56.5％。α相的硬度由273 HV10提高到343 HV10,γ相的硬度由238 HV10提高到299 HV10,试验钢强度明显提升。氮元素对两相比例和奥氏体相韧性的双重影响导致试验钢低温冲击性能呈先上升后下降的趋势;更高的氮含量抑制疲劳裂纹萌生与拓展,是影响HPD-1双相不锈钢室温疲劳性能的主要因素。撕裂棱是疲劳断口的显著特征。     

低活化马氏体钢热变形行为及机理型本构建模研究

利用Gleeble-3500热模拟试验机研究了低活化马氏体钢在变形温度为850～950 ℃、应变速率为0.001～1 s^-1条件下的热变形行为。建立了流变应力本构方程，并评估了该方程的预测能力。绘制了低活化马氏体钢在不同应变下的热加工图。结果表明：在较高的应变速率条件下，该材料主要发生动态回复，在较高变形温度和较低应变速率下具有明显的动态再结晶特征；本构方程的预测结果与实验结果符合良好；变形温度870～930 ℃、应变速率0.001～0.01 s^-1和变形温度920～950 ℃、应变速率0.3～1 s^-1分别是真应变为0.4和0.6下最优的热加工区域。     

Design and characteristics of a new type laminar plasma torch for materials processing

Laminar plasma jet(LPJ) generated by laminar plasma torch(LPT) has a favorable temperature and velocity distribution. Thus, it is superior to the turbulent plasma jet in material processing.However, most of the reported LPTs usually operate at a relatively low output power with a relatively low arc voltage and thermal efficiency, which limits its capabilities. In this context, this paper attempts to design a new type of high-power LPT with a relatively low arc current and a high thermal efficiency. In the first section, the design principle of the main components is studied and discussed in detail, and a new high-power LPT is proposed. Then, the experimental characteristics of the proposed high-power LPT are examined. Experimental results reveal the following characteristics of the proposed LPT.(1) The max jet length of the proposed LPT reaches at 540 mm.(2) Its mean arc voltage is higher than 290 V when the LPT works with arc currents lower than 200 A, leading to an output power greater than 50 kW.(3) The mean thermal efficiency is higher than 50%. Lastly, the proposed LPT has been applied to spheroidize the aluminum oxide powers. The experiment results for the production of spherical powders show that the proposed LPT has a good characteristic for material processing.     

Modeling and design of 3-D MPPT for ultra low power RF energy harvesters

Radio-Frequency (RF) energy harvesting must cope with the limited availability and high variability of the energy source. In this paper, the modeling of an RF harvester for ultra low power environments is presented. A mathematical model based on theoretical analysis is developed. The model demonstrates that the maximum transferred power point is located in a three-dimensional space defined by the input capacitance, the output voltage, and the load resistance of the rectifier circuit. Moreover, the mathematical model returns results in substantial agreement with the SPICE simulation results, while guaranteeing a remarkable reduction of the required computation time. Furthermore, the paper reports the implementation of a mixed signal system for the 3-D MPPT, to be embedded in an RF harvester, in a 65 nm CMOS technology. The circuit exhibits a simulated power consumption lower than 100 nW, making this solution suitable for ultra low power harvesting.     

单一低渗透突出煤层水力冲孔工艺优化应用分析

为了有效提高单一低渗透突出煤层的瓦斯抽采效率，以高压水射流冲击理论为指导，针对平煤股份八矿己组突出煤层特征建立数值模型，模拟分析水力冲孔应力分布规律，通过现场实测分析冲孔有效影响范围，进一步优化设计冲孔参数、指导现场施工。现场应用表明，水力冲孔是一种行之有效的方法，对单一低渗透突出煤层实施水力冲孔卸压增透、提高瓦斯抽采效果具有重要意义。     

臭氧氧化-循环喷淋法处理钨钼选矿废水

采用臭氧氧化-循环喷淋法去除钨钼选矿废水中COD,研究了pH值、臭氧流量、循环频率对COD去除效果的影响。结果表明: 废水COD去除率随pH值、臭氧流量、循环频率增大而增加,在pH值为10、臭氧流量3.0 L/min、循环频率4.0次/min条件下,氧化120 min后废水COD含量由131 mg/L降至11.5 mg/L,COD去除率达91.2%,满足《污水综合排放标准》(GB 8978-1996)一级标准。与O₂、NaClO处理废水COD的对比试验结果表明,循环喷淋法结合O₃表现出较好的COD去除效果。     

载铜树脂处理高含盐氨氮废水的性能

针对高含盐氨氮废水，选择具有不同功能基团的树脂为载体，进行负载Cu2+改性制得载铜树脂并对其处理高含盐氨氮废水的性能进行研究。在筛选出最佳载铜树脂的基础上，研究pH及Na+浓度、树脂投加量、反应时间对载铜树脂处理高含盐氨氮废水效果的影响，通过对吸附氨氮前后的载铜树脂进行SEM和EDS表征分析并构建吸附动力学模型以进一步探究配位吸附的过程。结果表明，Cu2+可与螯合树脂D751稳定结合且在宽pH值下均表现出耐盐性和良好的氨氮吸附效果；在室温(25℃)、pH=11及Na+浓度4 g/L、树脂投加量8 g/L、反应时间60 min的条件下，D751载铜树脂对氨氮的去除率为34.8%。D751载铜树脂吸附氨氮后其表面出现明显的晶状结构物质，该物质可能为铜氨络合物。D751载铜树脂对高含盐氨氮的吸附符合准二级动力学模型。